Doing a simulation to cover my own butt

Simulations/MCP2515 - CANbus RESET Pin Configuration/LTSpice Schematic - MCP2515 RESET Pin.asc

@@ -0,0 +1,36 @@
+Version 4
+SHEET 1 1388 680
+WIRE 192 0 -48 0
+WIRE 192 64 192 0
+WIRE -48 176 -48 0
+WIRE 192 208 192 144
+WIRE 288 208 192 208
+WIRE 400 208 368 208
+WIRE 192 288 192 208
+WIRE -48 368 -48 256
+WIRE 192 368 192 352
+WIRE 192 368 -48 368
+WIRE 192 400 192 368
+FLAG 192 400 0
+FLAG 400 208 #RESET
+IOPIN 400 208 In
+SYMBOL res 176 48 R0
+SYMATTR InstName R1
+SYMATTR Value 100
+SYMBOL cap 176 288 R0
+SYMATTR InstName C1
+SYMATTR Value 10<31>
+SYMBOL res 384 192 R90
+WINDOW 0 0 56 VBottom 2
+WINDOW 3 32 56 VTop 2
+SYMATTR InstName R2
+SYMATTR Value 1k
+SYMBOL voltage -48 160 R0
+WINDOW 123 0 0 Left 0
+WINDOW 39 0 0 Left 0
+SYMATTR InstName V1
+SYMATTR Value 5
+TEXT -1112 224 Left 2 ;Constraints:\nVoltage source that MCP2515 accepts is 5 V.\nThe minimum operating voltage is 2.7 V.\nTo ensure this happens with a comfortable margin, we will design #RESET\nto remain below 2.7 V for at least 10 microseconds.
+TEXT -1112 -40 Left 2 ;Problem:\n(Taken from MCP2515 Datasheet [Page 57])\nIt is important to provide a RESET signal after power-up to ensure that the logic\nand registers are in their default state. A hardware Reset can be achieved\nautomatically by placing an RC on the #RESET pin (See Figure 9-1).\nThe values must be such that the device is held in Reset for a minimum of\n2 microseconds after V_DD reaches the operating voltage, as indicated\nin the electrical specification (t_RL).
+TEXT -1112 424 Left 2 !.tran 0 0.001 0 startup
+TEXT 424 0 Left 2 ;Result:\nThis way over-satisfies the requirements, but will stay with this since the parts are\nprobably cheapest, just lying around somewhere in these values.

Simulations/MCP2515 - CANbus RESET Pin Configuration/LTSpice Schematic - MCP2515 RESET Pin.log

@@ -0,0 +1,21 @@
+Circuit: * C:\SunseekerTelemetry\Simulations\MCP2515 - CANbus RESET Pin Configuration\LTSpice Schematic - MCP2515 RESET Pin.asc
+
+.OP point found by inspection.
+
+Date: Tue Feb 02 00:12:38 2021
+Total elapsed time: 0.025 seconds.
+
+tnom = 27
+temp = 27
+method = modified trap
+totiter = 2090
+traniter = 2090
+tranpoints = 1046
+accept = 1046
+rejected = 0
+matrix size = 4
+fillins = 0
+solver = Normal
+Matrix Compiler1: 100 bytes object code size  0.1/0.0/[0.0]
+Matrix Compiler2: 248 bytes object code size  0.1/0.0/[0.0]
+